Dalsteel Metals Pty Limited

Data Sheets

Aluminium Alloy // Commercial Alloy // 5754 - H22 Sheet and Plate

Chemical Element % Present

Spec: BS EN 573-3:2009

Alloy 5754

Manganese (Mn) 0.0 - 0.50
Iron (Fe) 0.0 - 0.40
Magnesium (Mg) 2.60 - 3.60
Silicon (Si) 0.0 - 0.40
Chromium (Cr) 0.0 - 0.30
Copper (Cu) 0.0 - 0.10
Manganese + Chromium (Mn+Cr) 0.10 - 0.60
Other (Each) 0.0 - 0.05
Others (Total) 0.0 - 0.15
Titanium (Ti) 0.0 - 0.15
Zinc (Zn) 0.0 - 0.20
Aluminium (Al) Balance
Physical PropertyValue
Density 2.66 g/cm³
Melting Point 600 °C
Thermal Expansion 24 x10^-6 /K
Modulus of Elasticity 68 GPa
Thermal Conductivity 147 W/m.K
Electrical Resistivity 0.049 x10^-6 Ω .m
Mechanical PropertyValue

Spec: BS EN 485-2:2008

Sheet & Plate - 0.2mm to 40mm

Proof Stress 130 Min MPa
Tensile Strength 220 - 270 MPa
Hardness Brinell 63 HB
Elongation A50 mm 7 Min %

Aluminium 5754 has excellent corrosion resistance especially to seawater and industrially polluted atmospheres.
It has higher strength than 5251. This high strength makes 5754 highly suited to flooring applications.

Applications
5754 is typically used in:
~ Treadplate
~ Shipbuilding
~ Vehicle bodies
~ Rivets
~ Fishing industry equipment
~ Food processing
~ Welded chemical and nuclear structures

Please note that Mechanical Properties shown are for H22.

Alloy Designations

Alloy 5754 also corresponds to the following standard designations and specifications but may not be a direct equivalent:

 

A95754

Al Mg3

Al 3.1Mg Mn Cr

AW-5754

Temper Types

The most common tempers for 5754 aluminium are shown below with H114 & H111 being the most common treadplate temper

  • O - Soft
  • H111 - Some work hardening imparted by shaping processes but less than required for H11 temper
  • H22 - Work hardened by rolling then annealed to quarter hard
  • H24 - Work hardened by rolling then annealed to half hard
  • H26 - Work hardened by rolling then annealed to three-quarter hard

Supplied Forms

Alloy 5754 is typically supplied as treadplate

  • Plate
  • Sheet

Weldability

Weldability – Gas: Excellent

Weldability – Arc: Excellent

Weldability – Resistance: Excellent

Brazability: Poor

Fabrication

Workability – Cold: Very good

Machinability: Average

 

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.

Get Adobe Reader

Certain files on this page will require the Adobe Reader software. We recommend using the latest version if you don't already have it. Click "Get Adobe Reader" image to download the latest version now.