Dalsteel Metals Pty Limited

Data Sheets

Aluminium Alloy // Commercial Alloy // 2014A T6511 Extrusion

Chemical Element % Present

Spec: BS EN 573-3:2009

Alloy 2014

Silicon (Si) 0.50 - 0.90
Iron (Fe) 0.0 - 0.50
Copper (Cu) 3.90 - 5.00
Zinc (Zn) 0.0 - 0.25
Manganese (Mn) 0.40 - 1.20
Magnesium (Mg) 0.20 - 0.80
Titanium (Ti) 0.0 - 0.15
Others (Total) 0.0 - 0.15
Chromium (Cr) 0.0 - 0.10
Nickel (Ni) 0.0 - 0.10
Other (Each) 0.0 - 0.05
Titanium + Zirconium (Ti+Zr) 0.0 - 0.20
Aluminium (Al) Balance
Physical PropertyValue
Density 2.82 g/cm³
Modulus of Elasticity 71 GPa
Electrical Resistivity 0.045 x10^-6 Ω .m
Thermal Conductivity 138 W/m.K
Thermal Expansion 23 x10^-6 /K
Melting Point 535 °C
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Rod & Bar - Up to 25mm Dia. & A/F

Tensile Strength 415 Min MPa
Proof Stress 370 Min MPa
Hardness Brinell 140 HB
Elongation A50 mm 5 Min %
Elongation A 6 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Bar - 25mm to 75mm Dia. & A/F

Proof Stress 415 Min MPa
Tensile Strength 460 Min MPa
Hardness Brinell 140 HB
Elongation A 7 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Bar - 75mm to 150mm Dia. & A/F

Proof Stress 420 Min MPa
Tensile Strength 465 Min MPa
Hardness Brinell 140 HB
Elongation A 7 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Bar - 150mm to 200mm Dia. & A/F

Proof Stress 350 Min MPa
Tensile Strength 430 Min MPa
Hardness Brinell 140 HB
Elongation A 6 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Tube - Up to 10mm Wall Thickness

Proof Stress 370 Min MPa
Tensile Strength 415 Min MPa
Hardness Brinell 140 HB
Elongation A 7 Min %
Elongation A50 mm 5 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Tube - 10mm to 40mm Wall Thickness

Proof Stress 400 Min MPa
Tensile Strength 450 Min MPa
Elongation A50 mm 4 Min %
Hardness Brinell 140 HB
Elongation A 6 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Profile - Up to 25mm Wall Thickness

Proof Stress 370 Min MPa
Tensile Strength 415 Min MPa
Elongation A50 mm 5 Min %
Hardness Brinell 140 HB
Elongation A 7 Min %
Mechanical PropertyValue

Spec: BS EN 755-2:2008

Profile - 25mm to 75mm Wall Thickness

Proof Stress 415 Min MPa
Tensile Strength 460 Min MPa
Hardness Brinell 140 HB
Elongation A 7 Min %

A high strength 4 to 5% Copper alloy produced in extruded bar and profile form, in the fully heat-treated condition (solution heat-treated & artificially aged).Normally stocked in the T6511 condition (stress relieved by controlled stretching) Except for sizes under 10mm diameter and over 203.2mm diameter. (T6 only). Over 203.mm diameter is manufactured to chemical composition Only.
Machinability of aluminium alloy 2014A is very good.
Typical applications of aluminium alloy 2014A are high strength componenets especially for use in the aerospace and defence industries.

Temper Types

This datasheet relates to temper T6511. The most common temper for aluminium alloy 2014A are:

  • T6 - Solution heat treated and artificially aged
  • T3 - Solution heat treated, cold worked and naturally aged
  • T6511 - Solution heat treated and stress-relieved by stretching then artificially aged with minor straightening after aging
  • T651 - Solution heat treated, stress relieved by stretching then artificially aged

Supplied Forms

Round Bar is stocked in the range 1/2inch to 10inch diameter.
Plate is stokced in thicknesses 1/2inch to 4 inch.

  • Bar
  • Plate

Corrosion Resistance

Resistance to atmospheric attack:

Poor, especially when exposed to water or salt

Environments.

To protect against atmospheric corrosion

in storage, lightly coat with Lanolin based protective

Oil.

For further information, please contact Sales Dept

 

 

 

 

 

Weldability

Brazing & Soldering - Not recommended

Oxygen - Not recommended

Inert Gas - Not recommended

Resistance, Spot, Beam - Excellent

Surface Treatment

Anodising

- Protective - Fair

- Bright - Unsuitable

- Hard - Good

- Colour - Fair (Dark colour only)

.

Plating

- Very Good

This Data is indicative only and as such is not to be relied upon in place of the full specification. In particular, mechanical property requirements vary widely with temper, product and product dimensions. All information is based on our present knowledge and is given in good faith. No liability will be accepted by the Company in respect of any action taken by any third party in reliance thereon.

Please note that the 'Datasheet Update' date shown above is no guarantee of accuracy or whether the datasheet is up to date.

The information provided in this datasheet has been drawn from various recognised sources, including EN Standards, recognised industry references (printed & online) and manufacturers’ data. No guarantee is given that the information is from the latest issue of those sources or about the accuracy of those sources.

Material supplied by the Company may vary significantly from this data, but will conform to all relevant and applicable standards.

As the products detailed may be used for a wide variety of purposes and as the Company has no control over their use; the Company specifically excludes all conditions or warranties expressed or implied by statute or otherwise as to dimensions, properties and/or fitness for any particular purpose, whether expressed or implied.

Advice given by the Company to any third party is given for that party’s assistance only and without liability on the part of the Company. All transactions are subject to the Company’s current Conditions of Sale. The extent of the Company’s liabilities to any customer is clearly set out in those Conditions; a copy of which is available on request.

Get Adobe Reader

Certain files on this page will require the Adobe Reader software. We recommend using the latest version if you don't already have it. Click "Get Adobe Reader" image to download the latest version now.